Raised access floors
Four raised access floor series made in Dammam: nSteelCement, nGroove, nHPL and nSDV. Load grades from 3.7 to 11.1 kN, tested to CISCA.
Which raised floor do you need?
The floor finish decides the series; what the floor carries decides the grade. nSteelCement is our main series and takes every finish, from carpet to marble on a board layer. We recommend 4.5 kN as the minimum for every office.
nSteelCement
Our main seriesSteel cementitious raised access floor for carpet, LVT and SPC, and for marble and stone on a board layer.
View nSteelCement →nGroove
PremiumPremium calcium sulphate raised access floor for hard finishes bonded directly.
View nGroove →nHPL
Antistatic high pressure laminate raised access floor.
View nHPL →nSDV
Static dissipative vinyl raised access floor.
View nSDV →The finish decides the series
| Carpet tiles, LVT or SPC | nSteelCement, laid straight onto the panel |
|---|---|
| Marble, stone, porcelain or parquet | nSteelCement with a plywood, cement board or fibreboard layer (our standard). nGroove (premium) where the finish must be bonded straight to the panel |
| Antistatic floor | nHPL, final finish already on |
| Static dissipative floor | nSDV, final finish already on |
The load decides the grade
Every series comes in the same CISCA-tested grades. General offices: 4.5 kN minimum. MEWPs and scissor lifts: 6.8 kN and above. Forklifts and stackers: heavy grades after a wheel-load check by Nord Floors engineering.
Load grades (all series)
| Grade | Concentrated | Impact | Ultimate | Uniform | Rolling, 10 passes | Rolling, 10,000 passes |
|---|---|---|---|---|---|---|
| 370 | 3.7 kN | 0.67 | 10.8 kN | 19.8 kN/م² | 3.0 kN | 2.2 kN |
| 450 | 4.5 kN | 0.67 | 13.5 kN | 23.3 kN/م² | 3.6 kN | 3.0 kN |
| 560 | 5.6 kN | 0.67 | 16.8 kN | 33.1 kN/م² | 4.5 kN | 3.6 kN |
| 680 | 6.8 kN | 0.67 | 20.1 kN | 42.6 kN/م² | 5.6 kN | 4.5 kN |
| 890 | 8.9 kN | 0.67 | 26.7 kN | 49.9 kN/م² | 6.7 kN | 5.6 kN |
| 1110 | 11.1 kN | 0.67 | 33.3 kN | 58.3 kN/م² | 8.9 kN | 6.7 kN |
Recommended minimum for offices: the 450 grade (4.5 kN). For MEWP access: 680 (6.8 kN) and above. Tested to CISCA Recommended Test Procedures for Access Floors. nGroove starts at the 450 grade.
Compare the four series
| nSteelCement | nGroove | nHPL | nSDV | |
|---|---|---|---|---|
| Core | Steel cementitious | High-density calcium sulphate | Steel cementitious | Steel cementitious |
| Finish | Carpet, LVT, SPC direct; stone on a board layer | Hard finishes bonded directly | Antistatic HPL, factory-applied | Static dissipative vinyl, factory-applied |
| Thickness | 33 mm | 40 mm | 35 mm | 34.5 mm |
| Finished floor height | 80–2000 mm | 80–2000 mm | 80–2000 mm | 100–2000 mm |
| Load grades | 3.7 to 11.1 kN | 4.5 to 11.1 kN | 3.7 to 11.1 kN | 3.7 to 11.1 kN |
| Fire | A1 | A1, 120-minute integrity to EN 1366-6 | A1 | A1 |
| Acoustic | IIC 58 | IIC 55 | IIC 58 | IIC 58 |
| Pedestal head | cross | round | flat | square |
| Stringers | Above 600 mm FFH | Above 600 mm FFH | Always | Always |
Source: Nordinfini technical data sheets.
Understructure rules
- nHPL and nSDV always sit on stringers.
- nSteelCement and nGroove are stringerless up to 600 mm finished floor height, with stringers above it.
- Up to 600 mm, pedestals are fixed with chemical (adhesive) anchoring; above 600 mm they are mechanically anchored to the slab.
- Pedestal heads by series: nSteelCement cross head, nGroove round head, nHPL flat head, nSDV square head.
Why steel cementitious for Saudi buildings
| Steel cementitious (nSteelCement, nHPL, nSDV) | Woodcore (chipboard) | |
|---|---|---|
| Core | Lightweight cementitious core in a welded steel shell | Compressed wood-chip board |
| Fire | Non-combustible, A1 | Combustible, typically Bfl to Dfl |
| Moisture | Does not swell | Made for dry conditions; swells and weakens if wet |
| Load range | 3.7 to 11.1 kN | Many systems light to medium grades |
| End of life | Steel shell fully recyclable | Board disposal |
How many perforated panels do you need?
Perforated panels and air grilles are sold by the piece, finished to match the floor around them. Our calculator takes the airflow from your cooling unit datasheet and tells you how many, step by step.
Questions consultants ask
Why does Nord Floors recommend 4.5 kN as a minimum?
Lighter grades can carry ordinary office loads, but a 4.5 kN panel is stiffer. It sounds more solid underfoot, transmits less footfall noise and holds up better over the life of the building. We recommend 4.5 kN as the minimum for every office.
Can I put marble or stone on a raised floor?
Yes. nSteelCement is our standard panel and takes marble, stone, porcelain and parquet: fix a plywood, cement board or fibreboard layer to the panels, then lay the finish on it. Carpet tiles, LVT and SPC go straight onto the panel. nGroove is our premium panel for projects that need the hard finish bonded straight to the panel with no board layer.
Can a MEWP or scissor lift be used on a raised access floor?
Yes, on 6.8 kN grades and above. Nord Floors floors at 6.8 kN carry MEWPs on site today. Forklifts and pallet stackers are possible on heavy grades after Nord Floors engineering checks the wheel loads.
When does a raised floor need stringers and mechanical anchoring?
nHPL and nSDV are gravity-laid systems, so they use stringers at every height, from the lowest. nSteelCement and nGroove are corner-locking systems, fixed to the pedestal heads at each corner, so they need stringers only above 600 mm finished floor height. Up to 600 mm, chemical (adhesive) anchoring of the pedestals is enough; above 600 mm, pedestals are mechanically anchored to the slab.
Which standard are Nord Floors raised floors tested to?
Nord Floors follows the CISCA (Ceilings & Interior Systems Construction Association) Recommended Test Procedures for Access Floors for concentrated, ultimate, uniform and rolling loads.
Is woodcore (chipboard) raised flooring suitable for Saudi Arabia?
Usually not the best choice. Woodcore panels have a compressed wood-chip (chipboard) core, made for dry indoor conditions. Coastal humidity in Jeddah and Dammam, water from cleaning or leaks, and wet works during construction can make the core swell and lose strength. Woodcore is combustible (typically Bfl to Dfl fire classes), and many woodcore systems are rated only at light to medium grades. Steel cementitious panels such as nSteelCement are non-combustible (A1), do not swell with moisture, carry 3.7 to 11.1 kN, and last the life of the building; the steel shell is fully recyclable at end of life.
When do I need nHPL or nSDV?
Only where the room needs antistatic (nHPL) or static dissipative (nSDV) flooring, such as data rooms, server rooms and control rooms. Both come with their final finish factory-applied.
How many perforated panels or air grilles does a room need?
Only as many as the cooling needs. They are sold by the piece, not by the square metre. Divide the airflow that reaches the floor (cooling units running, minus leakage) by the airflow one panel passes at the design underfloor pressure. Our perforated panel calculator walks you through it from your CRAC datasheet.
Is Nord Floors raised flooring made in Saudi Arabia?
Yes. All four series are manufactured by Nordinfini in Dammam Industrial Area 2 and supplied across Saudi Arabia and the GCC.